Safety and the application of protective coatings

Furthermore, he continues, that it requires a vision, a process, an effort, and the commitment of everyone in the organization for it to become a seamless part of the business and the culture.  It occurs when deliberate steps needed to accomplish the desired results are established.

Potter identifies eight key steps to take towards achieving zero injuries:

1. Break down the job of hitting zero injuries to macro and micro work areas

2. Look at your overall location (think macro, aka the big picture) and see it as a workplace

3. Identify what is in your workplace that can cause injury (identify hazards in the form of material, conditions, or activity)

4. Take steps to mitigate the hazards in the workplace to a lower level of risk

5. Take a look at your worksite (think micro, meaning local or where you are completing tasks)

6. Identify what is in your worksite that can cause injury (this is a close-up, focused look)

7. Identify what controls can be employed to reduce the risk of injury (decrease the exposure or impact of the hazard)

8. Ask yourself, “Do we want to reach zero injuries in our workplace and are we willing to put out the necessary effort?”

Safety is not just seeing and reporting hazards says Potter, but it involves taking the steps to mitigate hazards to a lower level of risk, in other words, "we are attempting to create a workplace where it is more difficult to get hurt. And, learning the process of recognizing and controlling hazards taking time." 

In the application of protective coatings, safety is of overriding importance with the following factors needing to be considered, as outlined by Pierre R. Roberge in Corrosion Basics - An Introduction, 2nd edition.

Surface Preparation Workers using abrasive blasting equipment should be furnished with good equipment in proper working order. They should be equipped with air-filter masks to prevent their breathing dust and scale. Clothing should be adequate and safe. Safety shoes should be worn. Necessary goggles or safety glasses should be mandatory. Ear plugs or protective ear coverings should be worn.

No equipment should be operated in areas where it will create sparks that might ignite explosive or flammable materials. It should not be operated where abrasives, scale, or overspray will damage or interfere with the operation of other equipment.

Some materials, particularly older coatings that are to be removed for recoating of structures, are considered hazardous and require special safety procedures. This includes lead-based paints and asbestos-based coatings. These materials, often including the blast media, may not be left on site after removal.  To develop a plan for removal, capture, and proper disposal of these materials, an industrial hygienist is needed.

Materials Coating materials are frequently flammable, explosive, or poisonous, and sometimes all three. The characteristics of any material used should be known in advance, and any necessary precautions must be taken and rigidly maintained during the progress of the job. In summary:

1) Coatings incorporating flammable or explosive materials should not be used in the vicinity of open flames, sparks, or electrical equipment. Every precaution should be taken to prevent accidental fire or explosion by prohibiting smoking, requiring the use of non-sparking tools, or whatever other safety requirements are appropriate.

2) When used in enclosed places, solvent concentrations should be kept both below the explosive limit and below the acceptable toxicity level. Both limits vary among materials, so safety rules should be a function of materials used. Ventilation of enclosed places should be continuous during the operation and for three hours afterward when explosive or flammable solvents are used. Safety-approved electrical equipment is mandatory.

Solvent vapors should be removed from tanks by suction because many vapors are heavier than air. Thus, the remotest and lowest ends of tanks should receive special attention. Workers should wear approved compressed-air masks. Shoes should have rubber soles and heels and no exposed steel nails.

Equipment Whenever ventilation is a factor, it should be planned carefully and checked frequently. When necessary, automatic equipment should be used to make constant checks of air for poisons or explosive concentrations. All riggings, lifts, platforms, hoses, or any other equipment used on the job should be inspected and maintained in safe order. Rigging should be done by experienced operators.

Safety Guidelines Plant safety practices should be known and understood by plant paint crews or by outside crews doing contract work. In addition, the advice of plant safety engineers should be solicited and recommendations followed. Published information is available from technical and trade associations, testing bureaus, and most important, is usually printed on labels and instruction sheets received with materials and equipment. All personnel should be experienced and properly trained, including Operator Qualification (OQ) training, where applicable.

For more coatings tips as well as the latest techniques and technologies in the industry, sign up for CoatingsPro Magazine, free to industry professionals.

FREE DOWNLOADS

White Paper: An Action Plan for Reducing Pipeline Failures, Costs with Corrosion in the Water Sector

Special Report: The Future of Corrosion Control, Insights from the Experts